Great condition X-382 located in Barcelona, with plenty of recent upgrades she is a beautiful boat, solid and fast.
Magnífico X-382, un verdadero crucero-regata ideal para regatas de club combinado con el crucero familiar, pues es un barco muy rápido, sólido y estable. 3 camarotes dobles con un baño con WC eléctrico y depósito de aguas negras. impuesto de matriculación español pagado, pero ahora está con bandera belga.
This X382 comes with a hand selected teak interior in the modern layout of 3 cabins.
CONSTRUCTION / CE-CERTIFICATION
The X-382 has been built in accordance with the European CE-Certification and meets the requirements of the CE-directive 94/25/CE for recreational crafts.
These rules require a certain minimum standard of hull and deck strength, structural bulkheads and stringer, keel and rudder and their attachment to the hull, safety and stability, engine installation, gas installation, sea cocks, manuals and documentation of all major installations.
Table of contents
HULL/DECK & HULL/DECK JOINT
Hull as well as deck are in hand laid E-glass reinforced on special high stress areas with Triaxial fibre glass in connection with a sandwich laminate using hard compressed Divinycell 15 mm as core material. Solid laminated around the keel reinforcement girder system, the engine install, the propeller, the rudder bearings as well as in connection with all through hull fittings.
Hull surface outside is made of white gelcoat with 3 blue waterlines and sheer line moulded into the freeboard. Deck reinforced around and under all deck hard ware fittings with marine plywood and/or aluminium plating instead of the hard compressed Divinycell foam in a thickness of 15 mm.
Surface of deck outside is gelcoat white and the antislip areas on side decks are light grey. Area around cabin windows is blue.
Hull and deck are glued together with a special polyester resin and are bolted together for each 100 mm with s/s screws.
BOTTOM REINFORCEMENT/MAST FRAME
The floor construction is a heavy welded bottom frame with keel floors, mast floors, lifting strap securing lugs made of TBS steel sections, longitudinally connected with same material.
The floor construction is heat galvanised and glassed into solid laminate.
The antimony hardened leadkeel, with cast iron top and with very low centre of weight.
The keel is fixed with s/s bolts. The surface of the keel is protected with one layer of GRP and filler.
The rudder blade is laminated in Triaxial fibre glass. The rudder stock is a solid aluminium rudder stock, tapered at both ends for strength and weight saving.
The lower rudder bearing is roller bearing for minimum resistance.
The wheel steering is type Whitlock with a rack and pinion system, the wheel diameter 150 cm is covered with leather.
For safety, the yacht is delivered with a spare tiller to be mounted on top of the top rudder bearing.
Main structural bulkheads are of marine plywood - 24 12 mm securely bonded to the hull and deck.
CHAIN PLATES/BOW FITTING
Side chain plates are of stainless steel bolted through to the transverse main bulkhead.
Chain plate permanent backstay: stainless steel bolted through to the longitudinal bulkhead.
Bow fitting: stainless steel bolted through the reinforced solid GRP bow with integral anchor roller, headsail loop and attachment for head stay + base for bow pulpit.
Chain plate for babystay supported by the longitudinal bulkhead.
Padeye chain plate for running backstay.
In keel a deep bilge. The steel girder floor is with limber holes to allow all water to be assembled in the bilge. An electrical bilge pump with a manual switch.
A hand operated bilge pump is mounted for operation in the cockpit to meet the demands from "special regulations".
The mast is a silver anodised triple spreader tapered mast.
Discontinous rod rigging- new 2008
New running rigging- 2012 including new genoa cars.
Mechanical adjustable high power kickvang. Rod kicker type.
All halyards, reefs, and control lines led to two winches on cabin top, operated from cockpit.
New textile babystay 2012
Permanent backstay adjuster, hydraulic type Navtec operated with pump handle.
Carbon Spi pole
FURLEX genoa furler.
New removable davits for tender- 2012
Port de Roses, Local 10-11
Roses - Girona